Hardware Prerequisites

To ensure the performance and stability of Anypoint Platform Private Cloud Edition (Anypoint Platform PCE), every node in your Anypoint Platform PCE environment must meet the requirements described in this topic.

Before you install Anypoint Platform PCE, your infrastructure team must review each of the following sections and verify that your environment meets the stated disk and device requirements. If needed, contact your MuleSoft representative for assistance.

There are 2 components of PCE:

Anypoint Platform Core
Anypoint Monitoring (optional)

To ensure platform performance, stability, and high availability, Anypoint Platform Private Cloud Edition (Anypoint Platform PCE) supports two network configurations: 4-node and 7-node.

Small configuration:

4 nodes for Control Plane
3 additional nodes for Anypoint Monitoring (optional add-on)
NFS for asset storage
Load balancer

Large configuration:

7 nodes for Control Plane
3 additional nodes for Monitoring (optional)
NFS for asset storage
Load balancer

To ensure high availability and performance, each node must run on its own server in both configurations. If you are using a virtual machine to host the nodes, you must ensure that each VM node is running on a separate physical server.

Anypoint Platform Core

Prerequisites for 4-nodes or 7-nodes to run the Anypoint Platform Core.

Memory and CPU Requirements

The following are the minimum requirements needed for the Anypoint Platform core. Depending on your environment, you may need more CPU or memory.

Table 1. Memory and CPU Requirements
Component	Requirement
RAM	32 GB
CPU	8 Cores

If the stated requirements for Memory and CPU are not met, Anypoint Platform PCE installation will fail.

For production environments, each node in your configuration must have the following dedicated devices. All devices must be formatted either as xfs or ext4.

Table 2. Dedicated Device Requirements
Component	Size	Minimum IOPS	Mount Point	Description
HDD 2 System State Directory Device	250 GB	1500	/var/lib/gravity	Stores system configuration and metadata, including databases and packages. Because package sizes can be large, it is important to estimate the minimum size requirements and allocate enough space as a dedicated device before installation.
HDD 3 Application Data Device	250 GB	1500	/var/lib/data	Stores application configuration and data. The amount of space required should be at least 250 GB, but can vary depending on your specific use case. It is important to estimate the minimum size requirements and allocate enough space as a dedicated device ahead of time.
HDD 4 Docker Device	100 GB	3000	/var/lib/gravity/planet/docker	Used by Docker’s overlay storage driver. A minimum of 100GB is required for the overlay directory. Devices with 50GB or less will experience degraded system performance or might not work at all.
HDD 5 Etcd Device	20 GB	3000	/var/lib/gravity/planet/etcd	Provides dedicated storage for the distributed database used for cluster coordination.
/tmp (Installer)	50 GB	N/A
/ (root)	50 GB	N/A		You must have at least 50GB in your home directory to download and unzip the installer file.

The space requirements listed in the previous table are based on average use. For environments with heavy traffic, validate the amount of space needed with your Customer Success Manager.

System State Directory Device

The main purpose of the system state directory device is to store system configuration and metadata, for example, database and packages. As package sizes can be arbitrarily large, it is important to estimate the minimum size requirements and allocate enough space for the dedicated device.

Format this device either as xfs or ext4 and mounted as /var/lib/gravity.

The following shell snippet is provided as an example for mounting the system state directory device using systemd mount files and cannot be used as-is in production. You can also mount the system state directory device by using /etc/fstab or some other method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example to guide this process, make sure to specify the correct device name in two places.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/gravity
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/gravity\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-gravity.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-gravity.mount
sudo systemctl start var-lib-gravity.mount

Application Data Device

The main purpose of the application data directory device is to store application configuration and data. The minimum amount of space required is 250GB, but your use case might require more. It is important to allocate enough space for the dedicated device.

Format this device either as xfs or ext4 and mounted as /var/lib/data.

The following shell snippet is provided as an example for mounting the application data device using systemd mount files, and cannot be used as-is in production. You can also mount the application data device using /etc/fstab or some other method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example to guide this process, make sure to specify the correct device name in two places.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/data
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/data\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-data.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-data.mount
sudo systemctl start var-lib-data.mount

Etcd Device

The main purpose of the etcd device is to provide dedicated storage for a distributed database used for cluster coordination. It does not require much space, 20GB is adequate.

Format this device either as xfs or ext4 and mounted as /var/lib/gravity/planet/etcd.

The following shell snippet mounts the etcd device using systemd mount files to the path /var/lib/gravity/planet/etcd.

You can also mount the etcd device using /etc/fstab or another method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example as a guide for this process, specify the correct device name in two places.

Mount this device AFTER you mount the System State device under /var/lib/gravity/planet. If you are using systemd units to mount the volumes, declare mount dependencies using After=<device-name>.<mount>.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/gravity/planet/etcd
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/gravity/planet/etcd\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-gravity-planet-etcd.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-gravity-planet-etcd.mount
sudo systemctl start var-lib-gravity-planet-etcd.mount

Docker Device

Unless specified, Docker configuration defaults to the use of the overlay driver, which is recommended for production.

Format this device as xfs or ext4 and mount as /var/lib/gravity/planet/docker.

The following example shell snippet mounts the Docker device using systemd mount files to the path /var/lib/gravity/planet/docker. You can also mount the Docker device using /etc/fstab or another method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example as a guide for this process, replace <device name> with the correct device name in two places.

Mount this device AFTER you mount the System State device under /var/lib/gravity/planet. If you are using system.d units to mount the volumes, declare mount dependencies using After=<device-name>.<mount>

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/gravity/planet/docker
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/gravity/planet/docker\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-gravity-planet-docker.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-gravity-planet-docker.mount
sudo systemctl start var-lib-gravity-planet-docker.mount

Anypoint Monitoring

Anypoint Monitoring is an optional add-on that Anypoint Private Cloud supports. See Anypoint Monitoring on Anypoint Platform PCE for more information.

Prerequisites: The extra 3 nodes for the Monitoring Center Add-On.

Memory and CPU Requirements

Monitoring Center Add-On hardware requirements are different from the Platform Core nodes, they require more CPU, more memory and different disk mounts.

Table 3. Memory and CPU Requirements
Component	Requirement
RAM	128 GB
CPU	32 Cores

For production environments, each node in your configuration must have the following dedicated devices. All devices must be formatted either as xfs or ext4.

Table 4. Dedicated Device Requirements
Component	Size	Minimum IOPS	Mount Point	Description
HDD 2 System State Directory Device	250 GB	1500	/var/lib/gravity	Stores system configuration and metadata, including databases and packages. Package sizes can be large, so it is important to estimate the minimum size requirements and allocate enough space as a dedicated device before installation.
HDD 3 Docker Device	100 GB	3000	/var/lib/gravity/planet/docker	Used by Docker’s overlay storage driver. A minimum of 100GB is required for the overlay directory. Devices with 50GB or less will experience degraded system performance or might not work at all.
HDD 4 Cassandra AMV Device	500 GB	1500	/var/lib/data/dias-meld & /var/lib/data/dias-cassandra	Stores Cassandra database data for Monitoring Center Add-On. The amount of space required should be at least 250 GB, but can vary depending on your specific use case. It is important to estimate the minimum size requirements and allocate enough space as a dedicated device ahead of time.
HDD 5 Stolon AMV Device	250 GB	1500	/var/lib/data/stolon-amv	Stores Postgres database data for Monitorng Center Add-On. The amount of space required should be at least 250 GB, but can vary depending on your specific use case. It is important to estimate the minimum size requirements and allocate enough space as a dedicated device ahead of time.
HDD 7 InfluxDB AMV Device	4 TB	1500	/var/lib/data/influxdb	Stores InfluxDB data for Monitoring Center Add-On. The amount of space required should be at least 250 GB, but can vary depending on your specific use case. It is important to estimate the minimum size requirements and allocate enough space as a dedicated device ahead of time.
HDD 7 logstash AMV Device	500 GB	1500	/var/lib/data/logstash	Stores Logstash data for Monitoring Center Add-On. The amount of space required should be at least 250 GB, but can vary depending on your specific use case. It is important to estimate the minimum size requirements and allocate enough space as a dedicated device ahead of time.
/tmp (Installer)	20 GB	N/A
/ (root)	10 GB	N/A		You must have at least 10GB in your home directory to download and unzip the installer file.

The space requirements listed in the previous table are based on average use. For environments with heavy traffic, validate the amount of space needed with your Customer Success Manager.

System State Directory Device

Format this device either as xfs or ext4 and mount as /var/lib/gravity.

The following shell snippet is provided as an example for mounting the system state directory device using systemd mount files and cannot be used as-is in production. You can also mount the system state directory device by using /etc/fstab or some other method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example as a guide for this process, replace <device name> with the correct device name in two places.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/gravity
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/gravity\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-gravity.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-gravity.mount
sudo systemctl start var-lib-gravity.mount

Docker Device

Unless specified, Docker configuration defaults to the use of the overlay driver, which is recommended for production.

Format this device as xfs or ext4 and mount as /var/lib/gravity/planet/docker.

The following example shell snippet mounts the Docker device using systemd mount files to the path: /var/lib/gravity/planet/docker. You can also mount the Docker device using /etc/fstab or another method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example as a guide for this process, replace <device name> with the correct device name in two places.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/gravity/planet/docker
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/gravity/planet/docker\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-gravity-planet-docker.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-gravity-planet-docker.mount
sudo systemctl start var-lib-gravity-planet-docker.mount

DIAS Data Device

The main purpose of the DIAS Data directory device is to store Monitoring Center Add-On Cassandra and Meld database data. The minimum amount of space required is 250GB, but your use case might require more. It is important to allocate enough space for the dedicated device.

Format this device either as xfs or ext4 and mount as /var/lib/data.

The following shell snippet is provided as an example for mounting the application data device using systemd mount files, and cannot be used as-is in production. You can also mount the application data device using /etc/fstab or some other method. Consult with your system administrator to determine the best way to meet this requirement. If you use the following example as a guide for this process, replace <device name> with the correct device name in two places.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/data
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/data\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-data-dias.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-data-dias.mount
sudo systemctl start var-lib-data-dias.mount

Once mounted, create the following dirs if necessary on every Monitor Center Add-On node:

/var/lib/data/dias-cassandra
/var/lib/data/dias-meld

Stolon AMV Device

The main purpose of the Stolon AMV directory device is to store Monitoring Center Add-On Postgres database data. The minimum amount of space required is 250GB, but your use case might require more. It is important to allocate enough space for the dedicated device.

Format this device either as xfs or ext4 and mount as /var/lib/data/stolon-amv.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/data/stolon-amv
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/data/stolon-amv\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-data-stolon-amv.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-data-stolon-amv.mount
sudo systemctl start var-lib-data-stolon-amv.mount

InfluxDB AMV Device

The main purpose of the InfluxDB AMV directory device is to store Monitoring Center Add-On InfluxDB data. The minimum amount of space required is 250GB, but your use case might require more. It is important to allocate enough space for the dedicated device.

Format this device either as xfs or ext4 and mount as /var/lib/data/influxdb.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/data/influxdb
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/data/influxdb\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-data-influxdb.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-data-influxdb.mount
sudo systemctl start var-lib-data-influxdb.mount

Once mounted, create the following dirs if necessary on every Monitor Center Add-On node:

/var/lib/data/influxdb/data
/var/lib/data/influxdb/meta

Logstash AMV Device

The main purpose of the Logstash AMV directory device is to store Monitoring Center Add-On Logstash database data. The minimum amount of space required is 250GB, but your use case might require more. It is important to allocate enough space for the dedicated device.

Format this device either as xfs or ext4 and mount as /var/lib/data/logstash.

sudo mkfs.ext4 /dev/<device name>
sudo mkdir -p /var/lib/data/logstash
echo -e "[Mount]\nWhat=/dev/<device name>\nWhere=/var/lib/data/logstash\nType=ext4\n[Install]\nWantedBy=local-fs.target" | sudo tee /etc/systemd/system/var-lib-data-logstash.mount
sudo systemctl daemon-reload
sudo systemctl enable var-lib-data-logstash.mount
sudo systemctl start var-lib-data-logstash.mount

Verify Devices

To verify that all devices are set up the same way on all nodes, run the lsblk command on the Anypoint Monitoring and Visualizer nodes. Output from lsblk should resemble the following example:

[root@ip-0-0-0-0 ~]# lsblk
NAME    MAJ:MIN RM  SIZE  RO TYPE MOUNTPOINT
xvda    202:0    0   90G   0 disk
├─xvda1 202:1    0    1M   0 part
└─xvda2 202:2    0   90G   0 part /
xvdb    202:16   0  100G   0 disk /var/lib/gravity/planet/docker
xvdd    202:48   0  250G   0 disk /var/lib/data
xvde    202:64   0  250G   0 disk /var/lib/gravity
xvdf    202:64   0  250G   0 disk /var/lib/data/stolon-amv
xvdg    202:64   0  250G   0 disk /var/lib/data/influxdb
xvdh    202:64   0  250G   0 disk /var/lib/data/logstash
xvdi    202:64   0   20G   0 disk /tmp

Verify Disk IOPS

Depending on your hardware or virtualization provider, you can configure disk IOPS (I/O operations per second). Using the iops command, verify available IOPS on each device:

$ sudo ./iops --time 2 /dev/xvdb
/dev/xvdb, 107.37 GB, 32 threads:
 512   B blocks: 1893.0 IO/s, 946.5 KiB/s (  7.8 Mbit/s)
   1 KiB blocks: 1354.8 IO/s,   1.3 MiB/s ( 11.1 Mbit/s)
   2 KiB blocks: 1091.8 IO/s,   2.1 MiB/s ( 17.9 Mbit/s)
   4 KiB blocks:  807.1 IO/s,   3.2 MiB/s ( 26.4 Mbit/s)
   8 KiB blocks:  803.7 IO/s,   6.3 MiB/s ( 52.7 Mbit/s)
  16 KiB blocks:  787.4 IO/s,  12.3 MiB/s (103.2 Mbit/s)
  32 KiB blocks:  700.8 IO/s,  21.9 MiB/s (183.7 Mbit/s)
  64 KiB blocks:  590.0 IO/s,  36.9 MiB/s (309.3 Mbit/s)
 128 KiB blocks:  327.6 IO/s,  40.9 MiB/s (343.5 Mbit/s)
...

Load Balancer Requirements

Anypoint Platform PCE must run in a production environment with multiple servers. To distribute traffic among servers and to restrict access to specific ports, you must provide and configure a load balancer.

You can use any load balancer, including NGINX, but NGINX is not required.

If using the AWS Provisioner for Anypoint Platform PCE, you do not need to configure a separate load balancer. An Amazon ELB with the required configuration is created during installation.

Load Balancer Configuration

You can configure your load balancer to use any method for distributing client requests, but in most contexts a round robin strategy is ideal. The load balancer should be accessible through an IP address that is available to all machines in your network.

Your load balancer must route the following TCP ports:

Table 5. TCP Port Routing Requirements
Load Balancer Port	Instance Port	Internal Usage
`80`	`30080`	HTTP redirects to HTTPs
`443`	`30443`	HTTPS port
`8083`	`30883`	HTTPS port for Mule runtimes to authenticate and renew certificates
`8889`	`30889`	WebSocket port for Mule runtimes to connect
`8895`	`30895`	(Only when Monitoring Center is enabled)
`9500`	`32009`	Ops Center access port

In each case, your load balancer must listen on the load balancer port and redirect incoming requests to the instance port. Your Anypoint Platform PCE installation includes an internal NGINX server that listens on each of the configured instance ports, and then performs the action listed in the Internal Usage column.

Your load balancer should poll the address HTTP:10256/healthz to run a health check on your platform servers and confirm that they are accessible.

Do not configure SSL certificates in your load balancer. TLS termination is handled by the platform with the certificates configured using Access Management. See Configure Anypoint Platform PCE.

Implement a Load Balancer Using NGINX

Enable stream block in your /etc/nginx/nginx.conf file by referencing all the configuration properties defined in /etc/nginx/stream.d/*.
```
stream {
   include /etc/nginx/stream.d/*.conf;
}
```
Delete the default.conf file from /etc/nginx/conf.d
Create a folder named /etc/nginx/stream.d and in it create a file named onprem.conf

Paste the following content in onprem.conf

server {
   listen 80;
   proxy_pass 0.0.0.0:30080;
}

server {
   listen 443;
   proxy_pass 0.0.0.0:30443;
}

server {
   listen 8083;
   proxy_pass 0.0.0.0:30883;
}

server {
   listen 8889;
   proxy_pass 0.0.0.0:30889;
}

server {
   listen 8895;
   proxy_pass 0.0.0.0:30895;
}

server {
   listen 9500;
   proxy_pass 0.0.0.0:32009;
}

server {
   listen 9501;
   proxy_pass 0.0.0.0:30083;
}

Enable the default ports on SELinux before starting the NGINX. Run the following commands one by one:

semanage port -a -t http_port_t  -p tcp 8083
semanage port -a -t http_port_t  -p tcp 8889
semanage port -a -t http_port_t  -p tcp 8895
semanage port -a -t http_port_t  -p tcp 9500
semanage port -a -t http_port_t  -p tcp 9501

Start NGINX:
```
service nginx restart
```

Hardware Prerequisites

Anypoint Platform Core

Memory and CPU Requirements

System State Directory Device

Application Data Device

Etcd Device

Docker Device

Anypoint Monitoring

Memory and CPU Requirements

System State Directory Device

Docker Device

DIAS Data Device

Stolon AMV Device

InfluxDB AMV Device

Logstash AMV Device

Verify Devices

Verify Disk IOPS

Load Balancer Requirements

Load Balancer Configuration

Implement a Load Balancer Using NGINX

See Also